How To Clean Hi Point 9mm Handgun

Go THE C9 Hither FROM $139

Ohio-based Hi-Point has been delivering an assortment of pistols and carbines to the consumer market since 1994 just they can be somewhat difficult to clean and disassemble.

To requite the discussion direct from the company, Mike Strassell, Hi-Signal's owner, goes for a deep dive on the inner workings of the C9 series 9mm pistol in the in a higher place 21-infinitesimal video. The education also helps those with a Hi-Betoken CF380 or CF380 Comp model as the full disassembly and associates process is the same.

While non equally piece of cake every bit maintaining a mod revolver or something like, say a Glock, the job of breaking the C9 down to its component pieces isn't rocket science. Strassell does point out that those electing to tackle the job need to start with an unloaded pistol, empty magazine, a variety of punches (3/32, 1/8, i/sixteen) a block, assorted screwdrivers, the adjustment tool that comes with the gun, and a small-scale hammer.

Every bit for cleaning once the handgun is disassembled, HI-Signal notes in their recently updated user's manual for the C380/C9 the post-obit procedure:

Barrel: Make clean the butt as follows:
1. Moisture a cleaning patch with a gun cleaning solvent or a cleaner-lubricant- preservative and run it through the barrel, from the chamber end, several times using a cleaning rod.

2. Moisture a bristled cleaning brush with gun cleaning solvent or a cleaner-lubricant preservative and run information technology back and forth in the barrel, from the chamber finish, using a cleaning rod.

3. Wet a new cleaning patch with gun oil or a cleaner-lubricant-preservative and run information technology through the barrel once, from the chamber end, with the cleaning rod and examine information technology. If it is not clean, repeat steps two and 3 until the patch remains clean later on existence run through the barrel.

4. Before firing your Hullo-Point pistol, run a clean patch through the barrel, from the sleeping accommodation cease, using the cleaning rod. Echo this procedure until the patch comes out of the barrel with no gun oil or cleaner-lubricant-preservative on information technology. (Note: If y'all will exist storing your Hi-Point pistol, do not perform footstep 4 until y'all are gear up to use information technology).

5. Wet a nylon bristle brush with gun cleaning solvent or a cleaner-lubricant-preservative and thoroughly brush the outside of the barrel to remove any clay or residue.

6. Wipe the exterior of the barrel dry with a make clean patch and examine information technology. If information technology is not clean, repeat steps 5 and 6 until the patch remains clean.

SLIDE: Clean the slide as follows:

ane. Wet a nylon bristle brush with gun cleaning solvent or a cleaner-lubricant-preservative and thoroughly brush the bottom surfaces where the slide sits on the frame.

two. Wipe the bottom surfaces where the slide sits on the frame with a clean patch and examine it. If it is not clean, repeat steps ane and ii until the patch remains clean.

3. Moisture a nylon bristle brush with gun oil or a cleaner-lubricant-preservative and, while belongings the slide with the cage end facing down, castor the breech face up and the area under the extractor. Practice not use solvents on hydro dipped coated surfaces.

4. While holding the slide with the muzzle finish facing down, wipe the breech face with a make clean patch and examine it. If it is non clean, repeat steps 3 and 4 until the patch remains make clean.

5. Check all other exposed areas of the slide for cleanliness. If whatever dirt or debris is found, remove it with gun cleaning solvent or a cleaner-lubricant-preservative using a nylon bristle castor or a clean patch.

vi. Wipe the exposed areas of the slide that you have cleaned in footstep v with a make clean patch and examine information technology. If information technology is non clean, echo steps 5 and half-dozen until the patch remains clean.

FRAME: Check the frame for cleanliness. If necessary, make clean the frame as follows:

1. Wipe exposed parts of the frame with a clean patch that has been slightly dampened with gun cleaning solvent or a cleaner-lubricant- preservative.

2. Wipe the exposed areas of the frame with a clean patch and examine it. If it is non clean, repeat steps 1 and 2 until the patch remains make clean.

MAGAZINE: Inspect the magazine for clay or visible impairment. If necessary, make clean the mag equally follows:

i. Wipe the exterior of the mag and the feed lips with a clean patch that has been slightly dampened with gun cleaning solvent or a cleaner-lubricant-preservative.

two. Wipe the exterior of the magazine and the feed lips with a clean patch and examine information technology. If it is not clean, repeat steps 1 and two until the patch remains clean.

After you accept cleaned your Hi-Point pistol, lubricate it past slightly dampening a clean patch with gun oil or a cleaner-lubricant-preservative and wiping the outside of the barrel, the inside of the slide and the outside of the mag.

Your Hi-Bespeak pistol is designed to operate properly with simply a small amount of lubrication. Exercise not over lubricate your Hi-Bespeak pistol because besides much lubricant can collect unburned powder and other debris and preclude your Hi-Point pistol from functioning properly.

After you have finished cleaning and lubricating your Hello-Indicate pistol, and before y'all assemble information technology, y'all should inspect the barrel for lead build-upwardly, bulges, cracks or obstructions and inspect the frame and slide for any corrosion or whatever visible damage.

In the video on disassembly, when switching to assembly, Strassell warns on what parts not to arrange — such as the drib safe counterweight — and reiterates Hi-Indicate's assurances that, should the user observe broken or damaged parts, the mill will "send out replacement parts for costless."

Also, Hi-Indicate reached out and wanted us to share this cautionary tale virtually the above video:

"This video shows how to completely disassemble (detail strip) the C-9 pistol and is intended for use by trained armorers/gunsmiths only. Users should never disassemble their C-9 pistols across the instructions in the Education manual. Further disassembly by untrained persons could crusade your Hi-Betoken pistol to malfunction and will void the warranty. Hello-Betoken pistols are covered past a lifetime warranty. If your C-9 pistol is non functioning properly, needs to have a worn or broken part replaced, or its internal components need to be cleaned (which is not usually necessary) please contact Strassell's Machine, Inc. or a qualified gunsmith."

Co-ordinate to statistics by federal regulators, Hi-Bespeak produced 14,805 semi-automatic .380-caliber pistols in 2022 along with another 31,210 chambered in 9mm, all backed up by a lifetime warranty.

The company made headlines across the greater gun community this year, first with their new second generation C9 pistol, to be named the YC9 "Yeet Cannon" after the results of an online public poll. In commemoration of the public outpouring, Hi-Point has also released a special version of the C9 dubbed the "Yeet Cannon G1."

GET THE YEET CANNON HERE FROM $169

The original C9 is at present considered by many to be the Gen ane Yeet Cannon

Source: https://www.guns.com/news/2019/08/23/the-secret-to-hi-point-c9-cleaning-disassembly-revealed

Posted by: geiersquou2000.blogspot.com

Share this post